• -20%
Ravel Fire Alarm 8 Zone Control Panel
  • Ravel Fire Alarm 8 Zone Control Panel

Ravel Fire Alarm 8 Zone Control Panel

₹19,200 Save 20%
No tax

8 Zone LCD Control panel



Security policy


Delivery policy


Return policy

·        Switched Mode Power Supply.

·        Modular Construction

·        Auto Resettable Fuse

·        Surge Protection for all Input and outputs.

·        Programmable AC loss delay/Trouble Remainder/Alarm Verification

·        Battery polarity reversible protection

·        Surface Mount Technology

·        Over All current consumption is low.

·        Fully complies with UL -864 and NFPA-72.

·        Rugged CRCA sheet with powder coated finish.

·        Operates on 110 – 220v 50 /60 Hz, AC Mains power supply.

·        16×2 Dot Matrix LCD Display.

·        4/8 Class B Style ‘B ‘ or Style ’C’ initiating device circuit (IDC).

·        All zones accept smoke detectors and any normally open contact device.

·        Any Zone can be configured as Alarm or supervisory Zone.

·        2ClassBNotificationApplianceCircuits(NAC).

·        NAC shall be programmed as silenceable or Non Silenceable.

·        Supervisory Zone shall be Latching or Resettable.

·        Standby (battery) backup 24v DC power supply with built in charger

·        Error free Fire / Fault status in unambiguous colored LED indication.

·        System ON indication.

·        Main, Standby status audible and visual indication.

·        Battery Low visual warning with audible tone.

·        FormC relays for fire, fault and supervisory.

·        Resettable / Steady 24V D.C. Output.

·        RS 485 Communication facility (Optional).

·        Lamp Test facility.

·        All field wiring circuits are Power limited except 110 – 220v AC and Battery.

·        All field wiring circuits are supervised.

·        Walk Test facility.

·        Zone Isolation facility with loop voltage cut off.

·        Earth fault annunciation facility at 0 ohms.

·        AC Low voltage cutoff.

·        Programmable AC loss delay / Alarm verification / Trouble reminder.                                                                                                                                

Primary Power
120 – 220VAC ± 10%, 50 Hz, 2.5Amps.


Standby Power
24V D.C (2 Nos of 12v, 12Ah Sealed Lead acid battery).
Quiescent current: 120mA

Initiating Device Circuits
All zones are Class B Style B/C operation (Programmable).
Normal Operating Voltage: 14 – 21 VDC.
Alarm Current: 15 – 30mA.
Short Circuit Current: 45mA Maximum.
Loop resistance: 100 ohms Maximum.
End-Of-Line Resistor: 3K9, 1/2watt
Standby Current: 7mA (2mA for Detectors)

Operating Condition
Operating Temperature 0 – 49° C/32-120° F.
Relative Humidity 93 ± 2% RH (non- condensing) at 32 ±2° C/90 ±3° F.


Charging Circuit
Charging Voltage 28.2V, ±0.5V
Charging Current 800mA (Max.).

Notification Appliance Circuits
Class B Style – Y wiring
Operating Nominal Voltage: 24VDC
Special Application Current for all NACs: 1.2Amps (0.6A per circuit)
Line Drop: 1.8V
End-Of-Line Resistor: 3K9, 1/2watt

D.C. Output
Supervised 24VDC regulated, 300mA Max.


Common Relays
Type : Form C
No of Relays : 3
Relay Contact Rating : 2Amps @ 30 VDC,
0.5Amps @ 125VAC.
Power Factor : 1.0




(440W X 340H X 120D)



Red / White



18 Gauge (1.22mm) CRCA sheet with powder-coated Finish

IP Rating



Cable Entry


11xø19mm Knockout in top of the cabinet
10xø22.25mm Knockout in top of the cabinet

Comments (0)
No customer reviews for the moment.